 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| So You Want to Know Connectors . . . . . A REFERENCE GUIDE to Cylindrical Connectors Amphenol 0 This booklet is intended to be used as a ready reference to typical standard, miniature and subminiature cylindrical connector part numbers and terminology. Reading its brief pages will not make you a connector expert, but should guide you in becoming familiar with the product, in order to better serve our customers. Note: Many of the connector products in this brochure were formerly known as "Bendix" products. These products are now manufactured and sold under the Amphenol (R) brand name. The name "Amphenol" will replace the name "Bendix" on products and literature in the future. Contents SECTION I Nomenclature: Cylindrical Connectors ................................. 2-4 Basic Components Know the Language SECTION II Major MIL-Specifications by Type Standard, MIL-C-5015 Amphenol 97 Series Heavy Duty, MIL-C-22992 Proprietary Variations ........................................................... 5-6 MIL-C-5015 and 97 Series Part Number Breakdown MIL-C-22992 Part Number Breakdown SECTION III Major MIL-Specifications by Type Miniature, MIL-C-26482 ...................................................... 7-11 MIL-C-26482 Part Number Breakdown Miniature Crimp, Solder Part Number Breakdown SECTION IV Major MIL-Specifications by Type Subminiature, MIL-C-38999, MIL-C-27599....................... 12-21 Subminiature - JT/LJT, Tri-Start, SJT Features JT/LJT Part Number Breakdown and Specifications LJT-R/JT-R and Accessories Cross Reference List Tri-Start Series III Part Number Breakdown and Specifications SJT Part Number Breakdown SECTION V Cross Reference Data ............................................................ 22 Amphenol Aerospace is a Certified ISO 9001 Manufacturer. 1 SECTION I Nomenclature: Cylindrical Connectors Basic Components 1. Shell (Houses Inserts & Contacts) 2. Insert (Dielectric Contact Insulator) Pin or Socket 3. Contact (Wire End Termination) (Electrical Engagement) 4. Coupling Nut 5. Accessories (Wire Seals, Cable Seals, Wire Support, etc.) Mated Pair PLUG RECEPTACLE SHELL COUPLING NUT INSERT ENVIRONMENTAL SEALING GROMMET Rear Accessory CONTACTS REAR ACCESSORIES Shell Styles WALL MOUNT RECEPTACLE DESIGNATION: 00 LINE MOUNT RECEPTACLE OR CABLE CONNECTING RECEPTACLE* DESIGNATION: 01 BOX MOUNT RECEPTACLE DESIGNATION: 02 SOLDER MOUNT RECEPTACLE (HERMETIC) DESIGNATION:IH JAM NUT RECEPTACLE DESIGNATION: 07 STRAIGHT PLUG DESIGNATION: 06 * This connector style is sometimes referred to as a cable connecting "plug." It does, however, mate with either a straight or 90 degree plug. 2 Shell Styles (Cont'd.) Coupling Threaded, Bayonet Shell Sizes (Typical MIL-C-5015) 8S, 10S, 10SL, 12S, 12, 14S, 14, 16S, 16, 18 20, 22, 24, 28, 32, 36, 40, 44, 48 "S" designates short shell and short contacts Inserts Insert (Pin or Socket) Insert & Grommet Assy. Shell size denotes mating thread diameter in 16ths of an inch. For example, a size 8 shell denotes 8/16 of an inch with a .5000-28 UNEF thread. * * * * Solder Crimp Metal Clip Retention Dielectric Retention Style Designation PLUG 06 08 09 05 RECEPTACLE 00 01 02 03 04 07 IH SHELL STYLES Straight Angle Flange Mount Receptacle Straight, Less Rear Accessory SHELL STYLES Wall Mount Cable Connecting or Line Mount Receptacle Box Mount Wall Mount, Less Rear Accessory Line Mount, Less Rear Accessory Jam Nut Solder Mount Hermetic May include a soft front interfacial seal (Bonded) if dielectric is hard, and a rear sealing grommet separate or attached. Contact and Contact Termination Style Pin - Crimp* Socket - Crimp* Pin - Solder Socket - Solder Sizes by Wire Gauge, Examples: *Crimp is removable 4/0 American Wire Gauge 4/0 22D American Wire Gauge 22-28 3 Contacts Know the Language 25 Common terms you should know Pin Socket * Shell - Houses insert and contacts * Insert - The dielectric or insulating inner core, holds contacts * Coupling Nut - Outer threaded or grooved ring which holds mated pair together * Jam Nut - Nut that holds receptacle to a panel * Bayonet Coupling - A non-threaded, ramp type of coupling * Contacts - Mechanical tip to which electrical engagement is accomplished * Pin Contact - Male half of a mated pair of contacts* * Socket Contact - Female half of a mated pair of contacts * Solder Contact - A contact to which wire is joined by soldering * Crimp Contact - A contact to which wire is joined by mechanical squeeze * Plug - The cable/coupling half of a mating pair * Receptacle - The panel/receiving half of a mating pair Crimp or Solder Usually separate from insert, shipped loose or in bulk, tools needed to crimp, install and remove. Usually installed in insert, frequently bonded in place. Contact Options: Solderless Wrap (Wire Wrap), PC Tail, Coaxial, Thermocouple, Triaxial, Fiber Optic, Filter Contact Sizes Contact Size American Wire Gauge Wire Size (AWG) 22D 22-28 22M 24-28 22 22-26 20 20-24 16 16-22 * Mating Pair - Two connectors that couple together. Shell size insert arrangement and rotation must be compatible * Plating - The metal finish applied to contacts and or shell components (protective) to resist corrosion and wear Contact Size American Wire Gauge Wire Size (AWG) 12 12-14 8 8-10 4 4-6 0 0-2 * Grommet - Resilient part at back of insert (attached or separate); gives wire moisture seal * Gland - Resilient ring in rear accessory, provides seal on jacketed cable * Sealing Plug - Plastic type slug, placed in unused grommet holes to seal * Grounding Fingers - A metal strap around plug shell for positive shell-to-shell conductivity/shielding * Hermetic - A connector with fused glass insert for air tightness * Mating/Unmating Forces - Torque required to couple/uncouple a mating pair of connectors or contacts * Rear Termination - An accessory which threads to back of shell * Strain Relief - A type of accessory which clamps wires for support * Potting Boot - A type of accessory which forms a mold for potting compound * EMI or RFI Backshell - A type of accessory to terminate wire shielding * Interface Seal - A resilient part on the face of pin inserts which provides moisture seal. *Note: Male half always goes into female. Accessories * Adapters - straight, 90, 75 - conduit, environmental, open wire bundle, EMI, etc. * Compression ring - wire seal * Clamp - cable sealing * Stain relief - clamp, kellems grip * Potting boot - straight, angle, universal 4 SECTION II Major MIL-Specifications by Type * Standard, MIL-C-5015 * Amphenol 97 Series * Heavy Duty, MIL-C-22992 * Proprietary Variations * Older larger series of connectors * Found on many pieces of military equipment and commercial applications * Mostly heavy current carrying connectors * Early types had only solder type contacts * Later revision to MIL Spec also added crimp type contacts * Amphenol supplies the solder type to the MIL Spec * Amphenol supplies both solder and crimp versions under proprietary part numbers * Several variations of basic MIL-C-5015 and MIL-C-22992 types are available in the same and additional contact arrangements, such as the QWL, QWLD, 10-214000 Series, 10-244000 Series and others. * See Amphenol catalog sections: - MIL-C-5015 Cylindrical 12-020, - MIL-C-5015 Modifications 12-021, - Heavy Duty Cylindrical 12-052, - Commercial Aircraft Cylindrical 12-101, - 97 Series (MIL-C-5015 Proprietary) 12-022, - GT Series Bayonet 12-024. * Basic part number for MIL-C-5015 Series as supplied by Amphenol is MS310X A, C, E, F or R * MIL-C-5015 threaded coupling - 1 key/keyway shell polarization MIL-C-5015 Shell Styles 3100 3101 3102 3106 3108 3107 Wall Mount Receptacle Cable Connecting Receptacle* Box Mount Receptacle Straight Plug 90 Plug Quick Disconnect Plug (97 Series only) Contact Sizes Contact Size American Wire Gauge Wire Size (AWG) 16 16-22 12 12-14 8 8-10 4 4-6 0 0-2 NORMAL POSITION MIL-C-5015 Part Number Shell Style MS* Military Standard 3102 A Class Insert Arrangement 18 Shell Size MIL-C-5015 -3 S Contact Type Alternate Rotation W *or 97 Series Proprietary Class A or C Class B Class E/F Class R Mating Halves * Plugs: MS3106, MS3107, MS3108 or 97-3106, 97-3107, 97-3108 * Receptacles: MS3100, MS3102, MS3101, 97-3101, 97-3100, 97-3102 Other Non-MIL-Mates, Flange Mounted * Flange Mounted Plug: FP3106, 97-5105 * Thru-bulkhead Receptacle: TBF See also 10-74XXX and 10-873XX in catalog section MIL-C-5015 Mods. for jam nut receptacles (Non-MIL) Alternate Positions of Insert Arrangements * This connector style is sometimes referred to as a cable connecting "plug." It does, however, mate with either a straight or 90 degree plug. POSITION W POSITION X POSITION Y POSITION Z 5 Heavy Duty Cylindrical Connectors * Class L - for the heaviest loads - Current range 40 to 200 amperes - Direct current or single/three phase, 60/400 Hertz alternating current - Automatic grounding for safety * QWLD - for most power and control circuits - Military qualified connectors and commercial equivalents available - Increased shell size for greater durability than similar standard connectors * Class L and QWLD have 5 key/keyway shell polarization and double stub thread coupling * QWL - a more economical, compact heavy duty design for commercial power and control applications; single key shell polarization and double stub thread coupling MIL-C-22992 Series Connectors Classes C, R and L Part Number Breakdown The ordering procedure for QWLD MS-Approved Connectors is illustrated by part number MS17343R20N27PW as shown below: Part Number MS17343 R 20 N 27 P W 7. Alternate Insert Rotations: Used to prevent cross-mating of connectors. Absence of a letter in this space indicates normal (0 ) position of the insert. See catalog for alternate insert rotation illustrations. See catalog 12-052 for proprietary equivalents such as 10194XXX Series. Also see catalog 12-053 for QWL Series. The ordering procedure for Class "L" Connectors is illustrated by part number MS90555C32412SY as shown below: Part Number MS90555 C 32 4 12 S Y 1 2 3 4 5 6 7 See code below: 1. MS Numbers MS90555 designates wall mount receptacle (power source) MS90556 designates straight plug MS90557 designates cable connecting receptacle without coupling ring MS90558 designates wall mount plug with coupling ring (equipment end) 2. Shell Finish C (conductive) for AC or N (non-conductive) for DC circuits 1 2 3 4 5 6 7 See code below: 1. MS Numbers MS17343 designates wall mount receptacle MS17344 designates straight plug MS17345 designates cable connecting receptacle MS17346 designates box mount receptacle MS17347 designates jam nut receptacle with rear accessory threads (wall mount) MS17348 designates jam nut receptacle (box mount) 2. Class C designates pressurized; used where circuit integrity is protected by a pressure differential R designates environmental; (see Heavy Duty Cylindrical catalog 12-052 for definition) 3. Shell Size Available in shell sizes 12 through 44. See catalog 12-052 for dimensional data 4. Shell Finish C for conductive or N for non-conductive 5. Insert Arrangement Current MS insert arrangements are listed in catalog 12-052, Heavy Duty Cylindrical 6. Contact Type "P" designates pin contacts; "S" for socket contacts 3. Shell Size Relates directly to current carrying capability Size 28 - 40 amperes Size 32 - 60 amperes Size 44 - 100 amperes Size 52 - 200 amperes 4. Main shell Key/keyway Position N designates normal position. Three other positions (4, 5 and 6) of the main shell key/keyway prevent cross-mating or incompatible voltages. Refer to the individual connector style descriptions in catalog 12-052 for applicability. 5. Insert Arrangement Determined by connector size (current carrying capability) and cable configuration to be accommodated. See catalog for insert arrangement pattern illustrations. 6. Contact Type "P" designates pin contacts. "S" for socket contacts. MS90555 and MS90557 are supplied with socket contacts only. MS90556 and MS90558 are supplied with pin contacts only. 7. Alternate Insert Rotation Used to prevent cross-mating of incompatible frequencies. Absence of a letter in this space indicates normal (0 ) position of the insert. See catalog for individual insert arrangement description. 6 SECTION III Major MIL-Specifications by Type * Miniature, MIL-C-26482 Miniature PT-Types MIL-C-26482 * Widely used smaller connectors * Extensive use on military equipment including aircraft as well as commercial applications * Available with either crimp or solder type contacts * 3 point bayonet coupling * Popular low cost series * 5 Key/keyway shell polarization * Amphenol supplies MIL-Spec types as well as proprietary versions * MS311X or PT, solder type contacts (Series 1) * MS312X or PT-SE, crimp type contacts (front release) (Series 1) * MS347X or PTS-DR, crimp type contacts (rear release) (Series 2) * Modifications of Basic Series are: - PT-CE, crimp type contacts (front release) no MIL P/N, intermates with MS connectors - PC, double stub threaded coupling - (available with either crimp or solder contacts) no MIL P/N, does not intermate with PT types - SP, same as PT except wider flanges for back panel mounting, anodic coating, no MIL P/N, intermates with MS connectors - DC, same as PT except resistant to aircraft fluids, no MIL P/N, intermates with MS connectors - Other modifications and specials available * For details on above series see Amphenol catalog sections: - "Miniature Cylindrical" 12-070 - "Commercial Aircraft Cylindricals" 12-101. MIL-C-26482 Series 2 is the same as MIL-C-83723 Series 1 and will intermate with all PT connectors. The Series features rear removable contacts - accessories are ordered separately. MIL-C-83723 Series 1 has been superseded by MIL-C-26482 Series 2. MS 347 Military Std. Crimp Type Class Shell Insert Size Arrangement Alternate Rotation MS 312 0 E - 22 - 55 P W MIL-C-26482 Part Number PT Crimp Series 1 Shell Style Contact Type MIL-C-26482 Part Number PT Solder Series 1 Shell Style Contact Type MS 311 0 E - 22 - 55 P X Military Std. Solder Type Class Shell Insert Size Arrangement Alternate Rotation MIL-C-26482 Part Number PTS-DR Series 2, Rear Release Crimp Shell Style Contact Type 0 L - 22 - 55 S Y Military 26482 Std. Series 2 Rear Release Crimp Class Shell Insert Size Arrangement Alternate Rotation 7 PTS-DR Part Number Breakdown To more easily illustrate ordering procedure, part number PTS00DRL-18-32PW( ) is shown as follows: PTS 1 00 2 DR 3 L 4 -18 5 -32 6 P 7 W 8 () 9 MS/PTS-DR MIL-C-26482, Series 2 To more easily illustrate ordering procedure, part number MS3470L18-32PW is shown as follows: MS 1 347 2 0 3 L 4 18 5 -32 6 P 7 W 8 See code below: 1. Connector Type Electroless nickel alloy plate 200C, conductive finish standard "PTS" designates bayonet lock connector "PTGS" designates plug with grounding fingers "PTPS" designates wall mounting receptacle with wide flange 2. Shell Style "00" designates wall mounting receptacle "01" designates cable connecting receptacle "06" designates straight plug "07" designates jam nut receptacle 3. Retention System "DR" designates dielectrically retained contacts 4. Service Class "L" designates fluid resistant, environmental Class "E" has been superseded by Class "L" 5. Shell Size "18" designates shell size. Shell sizes 8 through 24 available. 6. Insert Arrangement "18 - 32" designates insert arrangement 7. Contacts "P" designates pin contacts "S" designates socket contacts 8. Insert Rotation "W", "X", "Y", "Z" designate that insert is rotated in its shell from "normal" position. No letter required for normal (no rotation) position. 9. Finish Variation Suffix Indicate optional finishes as follows: (005) anodic coating - Alumilite(R) (200C) (014) olive drab cadmium plate over nickel (175C) (023) electroless nickel (standard on PTS-DR) (200C) See code below: 1. "MS" designates Military Standard 2. Specification Number "347" designates basic family number for MIL-C-26482, Series 2 crimp type 3. Shell Style "0" designates narrow flange wall mounting receptacle "1" designates cable connecting receptacle "2" designates wide flange wall mounting receptacle "4" designates jam nut receptacle "5" designates plug with grounding fingers "6" designates straight plug 4. Service Class "A" designates grommet seal, 200C, non-conductive anodic coating "L" designate fluid resistant, 200C, conductive electroless nickel finish "W" designates fluid resistant, 175C, olive drab cadmium over nickel, conductive finish, 500 hr. salt spray 5. Shell Size "18" designates shell size. Shell sizes 8 through 24 available. 6. Insert Arrangement "18 - 32" designates insert arrangement 7. Contact Configuration "P" designates pin contacts "S" designates socket contacts 8. Insert Rotation "W", "X", "Y", "Z" designate that insert is rotated in its shell from "normal" position. No letter required for normal (no rotation) position. 8 Miniature Crimp Connectors Part Number Breakdown Proprietary Part Number Construction for Miniature Crimp Connectors To more easily illustrate ordering procedures, part number PT00SE-20-41PW (SR) is shown as follows: Part Number PT 1 00 2 SE3 20 - 41 4 5 P 6 W 7 (SR) 8 MS 1 312 2 0 3 Part Number Nomenclatures for MS/PT Crimp Connectors to MIL-C-26482 Specification To more easily illustrate ordering procedures, part number MS3120E-20-41PW is broken down as follows: Part Number E4 20 - 41 5 6 P 7 W 8 See code below: 1. Connector Family PT designates standard olive drab cadmium plated Tri-Lock coupling connector SP designates connector similar to PT except for anodic coating and larger flange and mounting holes for back panel mounting of receptacles 2. Shell Style "00" designates wall mount receptacle "01" designates cable connecting receptacle "02" designates box mount receptacle "06" designates straight plug "07" designates jam nut receptacle "08" designates 90 plug 3. Service Class "SE" designates environmental crimp "SP" designates potted type crimp Both of the above are Amphenol proprietary versions of the MIL-C-26482 Series 1 crimp contact connector and offer 15 lbs. contact retention for size 20 contacts, 25 lbs. for size 16 contacts. "CE" designates environmental crimp "CP" designates potted type crimp Both of the above are original Amphenol crimp connectors and offer 7 lbs. contact retention for size 20 contacts, 9 lbs. for size 16 contacts. 4. "20" designates shell size. Shell sizes available are 8 through 24. 5. "20-41" designates insert arrangement 6. "P" designates pin contacts; "S" for socket contacts 7. "W" designates that insert is rotated in its shell from the standard position to alternate position W. The basic rotations are W, X, Y, and Z. No letter required for normal (no rotation) position. 8. "SR" designates a strain relief clamp. Deviation suffixes would be inserted here. For example, (005) would indicate the metal parts (except contacts) would have anodic coating. See code below: 1. "MS" designates Military Standard 2. "312" designates basic family number for MIL-Spec 26482 crimp type 3. Shell Style "0" designates wall mount receptacle "1" designates cable connecting receptacle "2" designates box mount receptacle "4" designates jam nut receptacle "6" designates straight plug "7" designates box mount receptacle with dual mounting holes "8" designates wall mount receptacle with dual mounting holes 4. Service Class "E" designates environmental resisting connector "F" designates environmental resisting connector with strain relief "P" designates potted type with potting boot 5. "20" designates shell size. Shell sizes available are 8 through 24. 6. "20-41" designates insert arrangement 7. "P" designates pin contacts; "S" for socket contacts 8. "W" designates that the insert is rotated in its shell from the standard position to alternate position W. The basic rotations are W, X, Y, and Z. No letter required for normal (no rotation) position. Cross Reference - Commercial PT to Comparable Military MS Types Amphenol P/N PT00SE PT01SE PT02SE PT06SE MF02SE MF00SE PT07SE PT08SE PT00SE(SR) PT01SE(SR) MS P/N MS3120E MS3121E MS3122E MS3126E MS3127E MS3128E MS3124E None MS3120F MS3121F Amphenol P/N PT06SE(SR) MF00SE(SR) PT07SE(SR) PT08SE(SR) PT00SP PT01SP PT02SP PT06SP PT07SP MS P/N MS3126F MS3128F MS3124F None MS3120P MS3121P MS3122P MS3126P MS3124P 9 Miniature Solder Connectors Part Number Breakdown Part Number Nomenclature for Miniature Solder Connectors To more easily illustrate ordering procedures, part number PT00A-20-41PW (SR) is shown as follows: Part Number PT 1 00 2 A3 20 - 41 4 5 P 6 W 7 (SR) 8 MS 1 311 2 0 3 Part Number Nomenclatures for MS/PT Solder Connectors to MIL-C-26482 Specification To more easily illustrate ordering procedures, part number MS3110E-20-41PW is shown as follows: Part Number E4 20 - 41 5 6 P 7 W 8 See code below: 1. Connector Family PT designates standard olive drab cadmium plated Tri-Lock coupling connector. This is the Amphenol(R) proprietary version of the MIL-C-26482 solder contact connector. PC designates a bright cadmium plated connector with double stub thread coupling SP designates connector similar to PT except for anodic coating and larger flange and mounting holes for back panel mounting 2. Shell Style "00" designates wall mount receptacle "01" designates cable connecting receptacle "02" designates box mount receptacle "06" designates straight plug "07" designates jam nut receptacle PTB designates thru-bulkhead receptacle PTI designates solder mount receptacle 3. Service Class "A" designates general duty backshell "C" designates pressurized receptacle "E" designates environmental resisting with grommet and nut "P" designates potted with potting boot "W" designates clamp assembly for moisture-proofing, multijacketed cables "H" designates hermetic seal receptacle 4. "20" designates shell size. Shell sizes available are 6 through 24. 5. "20-41" designates insert arrangement 6. "P" designates pin contacts; "S" for socket contacts 7. "W" designates that insert is rotated in its shell from the standard position to alternate position W. The basic rotations are W, X, Y, and Z. No letter required for normal (no rotation) position. 8. "SR" designates a strain relief clamp. Deviation suffixes would be inserted here. For example, (005) would indicate the metal parts (except contacts) would have alumilite plating. See code below: 1. "MS" designates Military Standard 2. "311" designates basic family number for MIL-Spec 26482 solder type 3. Shell Style "0" designates wall mount receptacle "1" designates cable connecting receptacle "2" designates box mount receptacle "4" designates jam nut receptacle "6" designates straight plug 4. Service Class "E" designates environmental resisting connector with grommet and clamping nut "F" designates environmental resisting connector with grommet and strain relief "P" designates potted type with potting boot 5. "20" designates shell size. Shell sizes available are 8 through 24. 6. "20-41" designates insert arrangement 7. "P" designates pin contacts; "S" for socket contacts 8. "W" designates that the insert is rotated in its shell from the standard position to alternate position W. The basic rotations are W, X, Y, and Z. No letter required for normal (no rotation) position. Cross Reference - Commercial PT to Comparable Military MS Types Amphenol P/N PT00A PT01A PT02A PT06A PT07A PT00C PT02C PT07C PTB PT00E PT01E PT02E PT06E PT07E MS P/N None None None None None None None None MS3119Ref MS3110E MS3111E MS3112E MS3116E MS3114E Amphenol P/N PT00E(SR) PT01E(SR) PT02E(SR) PT06E(SR) PT07E(SR) PT00P PT01P PT02P PT06P PT07P PT00W PT01W PT02W PT06W PT02H PT07H PT1H MS P/N MS3110F MS3111F None MS3116F MS3114F MS3110P MS3111P None MS3116P MS3114P None None None None None MS3114H MS3113H 10 Miniature Shell Styles Also see PTB - Thru- bulkhead, double-ended receptacle in Miniature Cylindrical catalog. Wall Mount Receptacle Cable Connecting or Line Mount Receptacle* Wide Flange - Back Panel Mount: MS3127 Box Mount, MS3128 Wall Mount MIL-C-26482 Box Mount Receptacle Class E Class F Solder Mount Receptacle (Hermetic) Class P Class H Class W (Non-MIL) Jam Nut Receptacle Shell Sizes 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 Contact Sizes Straight Plug Contact Size American Wire Gauge Wire Size (AWG) 20 20-24 16 16-20 12 12-14 * This connector style is sometimes referred to as a cable connecting "plug." It does, however, mate with either a straight or 90 degree plug. 11 SECTION IV Major MIL-Specifications by Type * Subminiature, MIL-C-38999 * MIL-C-27599 Subminiature - JT/LJT, Tri-Start, SJT * Preferred for new design by the Military * Greatest growth potential of all cylindricals * "State of the Art" technology and performance * MIL-C-27599 has molded-in solder type contacts * MIL-C-38999 has rear release, crimp removable contacts * SJT has features of both the JT and LJT and is a NATO preferred connector in Europe * MIL-C-38999 Series I & II will not intermate * MIL-C-27599 Series I & II will not intermate * MIL-C-38999 and MIL-C-27599, Series I and II will intermate respectively * For more information, see Amphenol catalog section: - 12-090, Subminiature Cylindrical Connectors designed to MIL-C-38999 and MIL-C-27599 - 12-092, Tri-Start Connector - MIL-C-38999 Series III - 12-091, SJT - Proprietary MIL-C-38999 type - 12-130, Coaxial Contact Catalog MIL-C-38999 Series I (LJT-R) * 100% scoop-proof * High density arrangements (up to 128 contacts) * Contact sizes 12 through 22D plus size 16, 12, 8 coax, and size 8 twinax * Bayonet coupling * DOD preferred * Corrosion resistant (500 hr. salt spray) finish available * Removable crimp, PCB, wire wrap, twinax, and coax contacts available * Options include Hermetics, Filters and Thermocouples * 5 key/keyway polarization with 4 alternate rotations * Shell grounding fingers are standard on all plug * Triple-web grommet seal * Available in a Fail Safe Lanyard Release plug: see Amphenol catalog section 12-160 for additional Fail Safe Lanyard Release information. MIL-C-27599 Series I (LJT-Solder) * 100% scoop-proof * Molded-in solder type contacts * Options include PCB, wire wrap contacts * High contact density (up to 128 contacts) * Shell grounding fingers standard on all plugs * Intermateable with MIL-C-38999 Series I * Bayonet coupling * 5 key/keyway polarization with 4 alternate rotations Series II (JT-R) * High density arrangements (up to 128 contacts) * Low silhouette, light-weight non-scoop-proof * Bayonet coupling * Contact sizes 12 through 22D plus size 16 & 22 coax * 5 key/keyway polarization with 4 alternate rotations * Removable crimp, PCB, wire wrap and coax contacts available * Corrosion resistant (500 hr. salt spray) finish available * Options include Hermetics, Filters and Thermocouples * Shell grounding fingers on plugs are an option * Triple-web grommet seal * Available in Fail Safe Lanyard Release plug Series II (JT-Solder) * Low profile, light-weight, non-scoop-proof * Molded-in solder type contacts * Options include PCB, wire wrap contacts * High contact density (up to 128 contacts) * Shell grounding fingers available as option on plug * Intermateable with MIL-C-38999 Series II * Bayonet coupling * 5 key/keyway polarization with 4 alternate clockings 12 Subminiature JT/LJT Part Number Breakdown PROPRIETARY PART NUMBER To more easily illustrate ordering procedure, part number JT00RE-22-2PA( ) is shown as follows: Part Number JT 1 00 2 RE3 224 2 5 P 6 A 7 () 8/9 "RP" for potting crimp applications - Supplied with spacer grommet and potting boot. "RE" for environmental crimp applications - Supplied with a grommet and compression nut (JT Series only). Can be supplied with strain relief integral with compression nut "RE (SR)." "RT" for environmental applications - Supplied without rear accessories. Design provides serrations on rear threads of shells. For additional information defining complete description of service class, consult Amphenol, Sidney, NY. 4. Shell Size JT shell sizes available from 8 through 24. LJT shell sizes available from 9 through 25. 5. Insert Arrangement: 22-2 designates insert arrangement. Refer to catalog 12-090 for additional insert patterns. 6. Contact Style "P" designates pin contacts; "S" designates socket contacts. 7. Alternating Keying "A" designates alternate keying connector assembly. Other basic alternate keys are "B", "C" and "D". No letter required for normal (no rotation) position. 8. "SR" designates a strain relief clamp. Strain reliefs are available only on "A", "C" and "RE" class connectors. 9. Finish variation suffix. Not applicable to box mounting style. Military Finish Data Finish plus "SR" Suffix See code below: 1. Connector Type: JT designates standard Junior Tri-Lock connector LJT designates long Junior Tri-Lock connector LJTS JTS designates high temperature connector LJTN JTN designates chemical and fuel resistant JTL designates miniature mounting dimensions JTLN designates miniature mounting dimensions - chemical resistant JTLS designates miniature mounting dimensions - high temperature LJTPQ JTPQ designates back panel mounted wall mounting receptacle LJTP JTP designates back panel mounted box mounting receptacle LJTPN JTPN designates back panel mounted - chemical resistant LJTPS JTPS designates back panel mounted - high temperature JTG* designates plug with grounding fingers JTNG* designates plug with grounding fingers - chemical resistant *Grounding fingers standard on all LJT plugs. Finish Finish Suffix 2. Shell Style "00" designates wall mount receptacle "01" designates line mount receptacle "02" designates box mount receptacle "06" designates straight plug "07" designates jam nut receptacle "08" designates 90-degree plug "I" designates solder mount receptacle - hermetic 3. Service Class: Solder contacts/connectors "P" for potting applications - These connectors are supplied with a potting boot. All shells are designed with integral features to retain potting boots "A" for general duty applications. "A (SR)" - threaded rear design with strain relief "C" for pressurized applications "C" (SR)" - threaded rear design with strain relief "H" for hermetic applications - Fused compression glass sealed inserts. Leakage rate less than .01 micron cu. ft/hr. (1 x 10-7 cc/sec.) at 15 psi differential. "Y" same as "H" with interfacial seal "T" for MS27599A applications - General duty - pressurized (receptacles only) Cadmium plated nickel base Olive drab cadmium plate nickel base Electroless nickel Anodic coating (Alumilite) Chromate treated (Iridite 14-2) A B F C (014) (023) (005) (011) (SR) (386) (424) (300) (344) MILITARY TYPES MS27473 E MS Number Service Class Shell Size Finish Insert Arrangement Contact Style (P or S) Alternate Keying -No letter required for normal position 14 A 18 P A Military Service Class E Environmental, same as RE T Environmental, same as RT Y Hermetically sealed, same as Y P Potting, same as RP For finish variations see finish data on following page. For MS depictions and dimensional data see applicable MILSpec. (MIL-C-38999, MIL-C-27599). 13 Amphenol Federal Vendor Identification/FSCM 77820 Subminiature JT/LJT Specifications CONTACT RATING Test Current Contact Size Solder & Crimp Hermetic Maximum Millivolt Drop Crimp* Maximum Millivolt Drop Solder* Hermetic* Contact Size Crimp Well Data Well Diameter Nominal Well Depth Solder Well Data W Diameter Nominal Well Depth 22M 22D 22 20 16 12 10 Power 3 5 5 7.5 13 23 33 2 3 3 5 10 17 NA 45 73 73 55 49 42 33 20 60 85 22M 22D 22 20 16 12 10 Power .028 .001 .0345 .0010 .0365 .0010 .047 . 001 .067 .001 .100 .002 .137 .002 .141 .141 .141 .209 .209 .209 .355 .029 .034 .036 .044 .078 .116 20 20 20 20 NA 85 60 85 85 NA +.004 -.000 +.004 -.000 +.004 -.000 +.004 -.004 +.000 -.004 +.004 -.002 NA .094 .094 .094 .125 .141 .141 NA * When tested using silver plated wire SERVICE RATING** Service Rating Suggested Operating Voltage (Sea Level) AC (RMS) DC Test Voltage (Sea Level) Test Voltage 50,000 Ft. Test Voltage 70,000 Ft. Test Voltage 110,000 Ft. M N I II 400 300 600 900 500 450 850 1250 1300 VRMS 1000 VRMS 1800 VRMS 2300 VRMS 550 VRMS 400 VRMS 600 VRMS 800 VRMS 350 VRMS 260 VRMS 400 VRMS 500 VRMS 200 VRMS 200 VRMS 200 VRMS 200 VRMS ** Please note that the establishment of electrical safety factors is left entirely in the designer's hands, since he is in the best position to know what peak voltages, switching surges, transients, etc. can be expected in a particular circuit. FINISH DATA Aluminum Shell Components Non-Hermetic Suffix Finish Military Proprietary Indicated Finish Standard for JT Types Listed Below Standard for LJT Types Listed Below Cadmium Plated Nickel Base Anodic Coating (Alumilite) Chromate Treated (Iridite 14-2) Olive Drab Cadmium Plate Nickel Base Electroless Nickel MS (A) MS (C) MS (B) MS (F) - (005) (011) (014) (023) JT/JTG/JTL/JTP JTS/JTPS/JTLS JTN/JTPN/JTLN LJT/LJTP LJTPS/LJTS LJTN/LJTPN Hermetic Connectors Suffix Material Finish Military Proprietary Indicated Finish Standard for JT Types Listed Below Indicated Finish Standard for LJT Types Listed Below Carbon Steel Shell Tin Plated Shell and Contacts Carbon Steel Shell Tin Plated Shell and Gold Plated Contacts Stainless Steel Shell Gold Plated Contacts MS (D) MS (E) (162) JT ( ) H/JT ( ) Y JTL ( ) H/JTL ( ) Y LJT ( ) Y/LJT ( ) H JTS ( ) Y JTLS ( ) Y LJTS ( ) Y 14 MIL-C-38999 LJT-R/JT-R and Accessories Cross Reference List Series or Accessory Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I MS Part No. MS20047AXX MS20047BXX MS20047FXX MS20048AXX MS20048BXX MS20048FXX MS27342AXX-1 MS27342BXX-1 MS27342CXX-1 MS27342FXX-1 MS27342AXX-2 MS27342BXX-2 MS27342CXX-2 MS27342FXX-2 MS27352AXX MS27352BXX MS27352CXX MS27352FXX MS27353AXX MS27353BXX MS27353CXX MS27353FXX MS27466EXXAXXP/S MS27466EXXBXXP/S MS27466EXXFXXP/S MS27466TXXAXXP/S MS27466TXXBXXP/S MS27466TXXFXXP/S MS27466PXXAXXP/S MS27466PXXBXXP/S MS27466PXXFXXP/S MS27467EXXAXXP/S MS27467EXXBXXP/S MS27467EXXFXXP/S MS27467TXXAXXP/S MS27467TXXBXXP/S MS27467TXXFXXP/S MS27467PXXAXXP/S MS27467PXXBXXP/S MS27467PXXFXXP/S MS27468EXXAXXP/S MS27468EXXBXXP/S MS27468EXXFXXP/S MS27468TXXAXXP/S MS27468TXXBXXP/S MS27468TXXFXXP/S MS27468PXXAXXP/S MS27468PXXBXXP/S MS27468PXXFXXP/S MS27469YXXDXXP MS27469YXXEXXP MS27470YXXDXXP MS27470YXXEXXP MS27471YXXDXXP MS27471YXXEXXP Amphenol Part No. 10-275197-XX7 10-275197-XX9 10-275197-XXG 10-275196-XX7 10-275196-XX9 10-275196-XXG 10-440390-XX7 (Series II) 10-440390-XX9 (Series II) 10-440390-XX5 (Series II) 10-440390-XXG (Series II) 10-241055 Series II 10-457452 Series I Description Series or Accessory II MS Part No. MS27472EXXAXXP/S MS27472EXXBXXP/S MS27472EXXCXXP/S MS27472EXXFXXP/S MS27472TXXAXXP/S MS27472TXXBXXP/S MS27472TXXCXXP/S MS27472TXXFXXP/S MS27472PXXAXXP/S MS27472PXXBXXP/S MS27472PXXCXXP/S MS27472PXXFXXP/S MS27473EXXAXXP/S MS27473EXXBXXP/S MS27473EXXCXXP/S MS27473EXXFXXP/S MS27473TXXAXXP/S MS27473TXXBXXP/S MS27473TXXCXXP/S MS27473TXXFXXP/S MS27473PXXAXXP/S MS27473PXXBXXP/S MS27473PXXCXXP/S MS27473PXXFXXP/S MS27474EXXAXXP/S MS27474EXXBXXP/S MS27474EXXCXXP/S MS27474EXXFXXP/S MS27474TXXAXXP/S MS27474TXXBXXP/S MS27474TXXCXXP/S MS27474TXXFXXP/S MS27474PXXAXXP/S MS27474PXXBXXP/S MS27474PXXCXXP/S MS27474PXXFXXP/S MS27475YXXDXXP MS27475YXXEXXP MS27476YXXDXXP MS27476YXXEXXP MS27477YXXDXXP MS27477YXXEXXP MS27478YXXDXXP MS27478YXXEXXP MS27479EXXCXXP/S MS27479TXXCXXP/S MS27480EXXCXXP/S MS27480TXXCXXP/S MS27481EXXCXXP/S MS27481TXXCXXP/S MS27482YXXEXXP Amphenol Part No. JT00REXX-XXP/S JT00REXX-XXP/S (014) JTS00REXX-XXP/S JT00REXX-XXP/S (023) JT00RTXX-XXP/S JT00RTXX-XXP/S (014) JTS00RTXX-XXP/S JT00RTXX-XXP/S (023) JT00RPXX-XXP/S JT00RPXX-XXP/S (014) JTS00RPXX-XXP/S JT00RPXX-XXP/S (023) JT06REXX-XXP/S JT06REXXP/S (014) JT06REXX-XXP/S JT06REXX-XXP/S (023) JT06RTXX-XXP/S JT06RTXX-XXP/S (014) JT06RTXX-XXP/S JT06RTXX-XXP/S (023) JT06RPXX-XXP/S JT06RPXX-XXP/S (014) JTS06RPXX-XXP/S JT06RPXX-XXP/S (023) JT07REXX-XXP/S JT07REXX-XXP/S (014) JTS07REXX-XXP/S JT07REXX-XXP/S (023) JT07RTXX-XXP/S JT07RTXX-XXP/S (014) JTS07RTXX-XXP/S JT07RTXX-XXP/S (023) JT07RPXX-XXP/S JT07RPXX-XXP/S (014) JTS07RPXX-XXP/S JT07RPXX-XXP/S (023) JT00YXX-XXP JTS00YXX-XXP JT02YXX-XXP JTS0YXX-XXP JT07YXX-XXP JTS07YXX-XXP JTIYXX-XXP JTSIYXX-XXP JTS00REXX-XXP/S JTS00RTXX-XXP/S JTS06REXX-XXP/S JTS06RTXX-XXP/S JTS07REXX-XXP/S JTS07RTXX-XXP/S JTS00YXX-XXP Description Cap, Recept. Series I No Chain II II II Cap, Plug Series I, No Chain II II II II II Wall Mount Receptacle Adapter II II II II II 10-241853-XX7 10-241853-XX9 10-241853-XX5 10-241853-XXG 10-241856-XX7 10-241856-XX9 10-241856-XX5 10-241856-XXG LJT00REXX-XXP/S LJT00REXX-XXP/S (014) LJT00REXX-XXP/S (023) LJT00RTXX-XXP/S LJT00RTXX-XXP/S (014) LJT00RTXX-XXP/S (023) LJT00RPXX-XXP/S LJT00RPXX-XXP/S (014) LJT00RPXX-XXP/S (023) LJT06REXX-XXP/S LJT06REXX-XXP/S (014) LJT06REXX-XXP/S (023) LJT06RTXX-XXP/S LJT06RTXX-XXP/S (014) LJT06RTXX-XXP/S (023) LJT06RPXX-XXP/S LJT06RPXX-XXP/S (014) LJT06RPXX-XXP/S (023) LJT07REXX-XXP/S LJT07REXX-XXP/S (014) LJT07REXX-XXP/S (023) LJT07RTXX-XXP/S LJT07RTXX-XXP/S (014) LJT07RTXX-XXP/S (023) LJT07RPXX-XXP/S LJT07RPXX-XXP/S (014) LJT07RPXX-XXP/S (023) LJT00YXX-XXP LJTS00YXX-XXP LJT07YXX-XXP LJTS07YXX-XXP LJTIYXX-XXP LJTSIYXX-XXP Wall Mount Recept., Hermetic Seal Jam Nut Mount Recept., Hermetic Seal Solder Mount Recept., Hermetic Seal Jam Nut Mount Receptacle Straight Plug Straight Plug Wall Mount Receptacle Cap, Recept. Series II, No Chain Cap, Plug Series II, No Chain II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II II Straight Plug Jam Nut Mount Receptacle Wall Mount Recept., Hermetic Seal Box Mount Recept., Hermetic Seal Jam Nut Mount Recept., Hermetic Seal Solder Mount Recept., Hermetic Seal Wall Mount Recept., Inactive, Use MS27472 Straight Plug, Inactive, Use MS27473 Jam Nut Mount Recept., Inactive, Use MS27474 Wall Mount Recept., Hermetic Seal, Inactive, Use MS27475 Jam Nut Mount Recept., Hermetic Seal, Inactive, Use MS27477 II MS27483YXXEXXP JTS07YXX-XXP 15 MIL-C-38999 LJT-R/JT-R and Accessories Cross Reference List (Cont.) Series or Accessory II II II II II II II II II Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac Ac I II II II II I & II I & II I I I II II II II II II II II II II II II II II II II MS Part No. MS27484EXXAXXP/S MS27484EXXBXXP/S MS27484EXXFXXP/S MS27484TXXAXXP/S MS27484TXXBXXP/S MS27484TXXFXXP/S MS27484PXXAXXP/S MS27484PXXBXXP/S MS27484PXXFXXP/S MS27485AXX MS27485BXX MS27485CXX MS27485FXX MS27486-XX-1 MS27486-XX-2 MS27487-XX-1 MS27487-XX-2 MS27488-12 MS27488-16 MS27488-20 MS27488-22 MS27489-XXX MS27490-XX MS27491-XX MS27492-XX MS27493-XX MS27494-XX MS27495R-XX MS27495A-XX MS27496EXXAXXP/S MS27496EXXBXXP/S MS27496EXXFXXP/S MS27497EXXAXXP/S MS27497EXXBXXP/S MS27497EXXCXXP/S MS27497EXXFXXP/S MS27497TXXAXXP/S MS27497TXXBXXP/S MS27497TXXCXXP/S MS27497TXXFXXP/S MS27497PXXAXXP/S MS27497PXXBXXP/S MS27497PXXCXXP/S MS27497PXXFXXP/S MS27497VXXAXXP/S MS27497VXXBXXP/S MS27497VXXCXXP/S MS27497VXXFXXP/S Amphenol Part No. JTG06REXX-XXP/S JTG06REXX-XXP/S (014) JTG06REXX-XXP/S (023) JTG06RTXX-XXP/S JTG06RTXX-XXP/S (014) JTG06RTXX-XXP/S (023) JTG06RPXX-XXP/S JTG06RPXX-XXP/S (014) JTG06RPXX-XXP/S (023) 10-528399-XX7 10-528399-XX9 10-528399-XX5 10-528399-XXG 10-241912-XX 10-241990-XX 10-450910-XX, Includes MS27489 10-450911-XX 10-405996-12 10-405996-16 10-405996-20 10-405996-24 10-352425-XX 10-407035-XX5 10-251416-XX5 10-251416-XXH 10-251415-XX5 10-251415-XXH 11-8675-XX 11-8674-XX LJT02REXX-XXP/S LJT02REXX-XXP/S (014) LJT02REXX-XXP/S (023) JTPQ00REXX-XXP/S JTPQ00REXX-XXP/S (014) JTPSQ00REXX-XXP/S JTPQ00REXX-XXP/S (023) JTPQ00RTXX-XXP/S JTPQ00RTXX-XXP/S (014) JTPSQ00RTXX-XXP/S JTPQ00RTXX-XXP/S (023) JTPQ002PXX-XXP/S JTPQ002PXX-XXP/S (014) JTPSQ002PXX-XXP/S JTPQ00RPXX-XXP/S (023) JTP00REXX-XXP/S JTP00REXX-XXP/S (014) JTPS00REXX-XXP/S JTP00REXX-XXP/S (023) Description Series or Accessory I I II II MS Part No. MS27498EXXAXXP/S MS27498EXXBXXP/S MS27499EXXAXXP/S MS27499EXXBXXP/S MS27499EXXCXXP/S MS27499EXXFXXP/S MS27500EXXAXXP/S MS27500EXXBXXP/S MS27501AXXC MS27501BXXC MS27501FXXC MS27502AXXC MS27502BXXC MS27502FXXC MS27503YXXEXXP MS27504EXXCXXP/S MS27505EXXAXXP/S MS27505EXXBXXP/S MS27505EXXFXXP/S MS27506AXX-1 MS27506BXX-1 MS27506FXX-1 MS27506AXX-2 MS27506BXX-2 MS27506CXX-2 MS27506FXX-2 MS27507A-XX MS27507B-XX MS27507C-XX MS27507F-XX MS27508EXXAXXP/S MS27508EXXBXXP/S MS27508EXXCXXP/S MS27508EXXFXXP/S MS27509R-XX MS27509A-XX MS27510AXXC MS27510BXXC MS27510CXXC MS27510FXXC MS27511AXXC MS27511BXXC MS27511CXXC MS27511FXXC MS27511AXXR MS27511BXXR MS27511CXXR MS27511FXXR MS27510 ( )XXR MS27511( )XXN Amphenol Part No. LJT08REXX-XXP/S LJT08REXX-XXP/S (014) JT02REXX-XXP/S JT02REXX-XXP/S (014) JTS02REXX-XXP/S JT02REXX-XXP/S (023) JT08REXX-XXP/S JT08REXX-XXP/S (014) 10-421399-XX7 10-421399-XX9 10-421399-XXG 10-427406-XX7 10-427406-XX9 10-427406-XXG JTSIYXX-XXP JTS00REXX-XXP/S LJTP02REXX-XXP/S (023) LJTP02REXX-XXP/S (014) LJTP02REXX-XXP/S (023) 10-436792-XX7 10-436792-XX9 10-436792-XXG 10-433992-XX7 10-433992-XX9 10-433992-XX5 10-433992-XXG 10-415693-XX7 10-415693-XX9 10-415693-XX5 10-415693-XXG JTP02REXX-XXP/S JTP02REXX-XXP/S (014) JTPS02REXX-XXP/S JTP02REXX-XXP/S (023) 10-296943-XX 10-296940-XX 10-241801-XX7 10-241801-XX9 10-241801-XX5 10-241801-XXG 10-241800-XX7 10-241800-XX9 10-241800-XX5 10-241800-XXG 10-241866-XX7 10-241866-XX9 10-241866-XX5 10-241866-XXG 10-24186410-241802- Description 90 Degree Plug, Inactive for Design Straight Plug with Grounding Spring II II II II I I Box Mount Receptacle 90 Degree Plug, Inactive for Design Cover, Plug, with chain Ring, Potting Boot, Series II I I I Cover Receptacle, with chain Solder Mount Receptacle, Hermetic Seal Inactive, use MS27503 Box Mount Receptacle, Inactive, use MS27499 Back Panel Wall Mount Receptacle Potting, Boot Straight, Series II Potting, Boot 90 Degree Series II Kit, EMR Adapter, Straight, Series I & II Kit, EMR Adapter, 90 Degree Series I & II, I II II I I I Plug, Sealing Grommet I I Adapter, Reducer EMR for use with MS27487 Contact-Socket Contact-Socket Contact-Socket, Inactive, use MS27491 Contact-Pin Contact-Pin, Inactive, use MS27493 Tool, Contact, Removable, Metal Tool, Contact, Assembly, Metal I II II II II I & II I & II I & II I & II II II II Adapter, Strain Relief, Clamp Bars Adapter, 90 Degree, Strain Relief, Clamp Bars Back Panel Box Mount Receptacle Box Mount Receptacle II I & II I & II II II II II II II Tool, Contact Removal and Assembly, Plastic Inactive, use MS27534 Cap, Plug with chain Back Panel Wall Mount Receptacle. II II II II II II II II Cap, Receptacle, with chain Cap, Receptacle with wire rope Cap, Plug with wire rope Cap, Receptacle, Jam Nut, with chain 16 MIL-C-38999 LJT-R/JT-R and Accessories Cross Reference List (Cont.) Series or Accessory II II II II II II II II II I I I I I I I & II I & II I & II I & II I I I I I I I I I I I I MS Part No. MS27512-XXA MS27512-XXB MS27512-XXC MS27512-XXE MS27512-XXF MS27513EXXAXXP/S MS27513EXXAXXP/S MS27513EXXCXXP/S MS27513EXXFXXP/S MS27514-XXA MS27514-XXB MS27514-XXE MS27514-XXF MS27515EXXAXXP/S MS27515EXXBXXP/S MS27534-12 MS27534-16 MS27534-20 MS27534-22D MS27535 MS27536 MS27652EXXFXXP/S MS27652TXXFXXP/S MS27653EXXFXXP/S MS27653TXXFXXP/S MS27654EXXFXXP/S MS27654TXXFXXP/S MS27655-XX MS27656EXXAXXP/S MS27656EXXFXXP/S MS27656EXXFXXP/S Amphenol Part No. 10-101917-XX7 10-101917-XX9 10-101917-XX5 10-260548-XX 10-101917-XXG JT02REXX-XXP/S JT02REXX-XXP/S (014) JTS02REXX-XXP/S JT02REXX-XXP/S (023) 10-123017-XX7 10-123017-XX9 10-195959-XX 10-123017-XXG LJTP00REXX-XXP/S LJTP00REXX-XXP/S (014) 10-538988-12 10-538988-16 10-538988-20 10-538988-22D 21-33101-XX 21-33102-XX LJTS00REXX-XXP/S (023) LJTS00RTXX-XXP/S (023) LJTS06REXX-XXP/S (023) LJTS06RTXX-XXP/S (023) LJTPS00REXX-XXP/S (023) LJTPS00RTXX-XXP/S (023) 10-407035-XXH LJTPQ00REXX-XXP/S LJTPQ00REXX-XXP/S (014) LJTPQ00REXX-XXP/S (023 Description Series or Accessory I I MS Part No. MS27656TXXAXXP/S MS27656PXXBXXP/S MS27656PXXFXXP/S MS27656PXXAXXP/S MS27656PXXBXXP/S MS27656PXXFXXP/S MS27661EXXAXXP/S MS27661EXXBXXP/S MS27661EXXFXXP/S MS27662EXXAXXC MS27662EXXBXXC MS27662EXXCXXC MS27662EXXFXXC MS27663AXX-1 MS27663BXX-1 MS27663CXX-1 MS27663FXX-1 MS27663AXX-2 MS27663BXX-2 MS27663CXX-2 MS27663FXX-2 MS27664EXXAXXP/S MS27664EXXBXXP/S MS27664EXXCXXP/S MS27664EXXFXXP/S MS27664TXXAXXP/S MS27664TXXBXXP/S MS27664TXXCXXP/S MS27664TXXFXXP/S MS27665 MS27666 DNS Amphenol Part No. LJTPQ00RTXX-XXP/S LJTPQ00RTXX-XXP/S (014) LJTPQ00RTXX-XXP/S (023) LJTPQ00RPXX-XXP/S LJTPQ00RPXX-XXP/S (014) LJTPQ00RPXX-XXP/S (023) 87-538800/74 88-538800/74 91-538800/74 LJTB-XX-XXX LJTB-XX-XXX LJTB-XX-XXX LJTB-XX-XXX 10-482790-XX7 10-482790-XX9 10-482790-XX5 10-482790-XX6 10-482494-XX7 10-482494-XX9 10-482494-XX5 10-482494-XX6 JTPQ00REXX-XXP/S JTPQ00REXX-XXP/S (014) JTPSQ00REXX-XXP/S JTPQ00REXX-XXP/S (023) JTPQ00RTXX-XXP/S JTPQ00RTXX-XXP/S (014) JTPSQ00RTXX-XXP/S JTPQ00RTXX-XXP/S (023) Description Back Panel Wall Mount Receptacle Nut, Hex I I I I Back Panel Wall Mount Receptacle Box Mount Receptacle, Full Length Grommet I I I I Straight Plug, Lanyard Release Nut, Hex I I I Thru-Bulkhead Mount Receptacle Black Panel Wall Mount Receptacle, Inactive, Use MS27656 I & II I & II I & II Adapter Nut, Non-Metallic (Nylon Only) Tool, Contact Insertion/ Removal, Plastic I & II I & II I & II Contact, Socket, Shielded Contact, Pin, Shielded Wall Mount Receptacle Inactive, Use MS27466 Straight Plug, Inactive, Use MS27467 Back Panel Wall Mount Recept. Inactive, Use MS27656 Contact, Socket, Inactive, Use MS27490 Back Panel Wall Mount Receptacle I & II I & II II II II II II II II II I Adapter 90 Degree, Non-Metallic (Nylon Only) Back Panel Wall Mount Receptacle, Inactive Use MS27497 Rack and Panel, Cancelled II II II MS27667EXXBXXC MS27667EXXCXXC MS27667EXXFXXC MS27668 MS27669 MS27670 JTB-XX-XX JTB-XX-XX JTB-XX-XX DNS DNS DNS Thru-Bulkhead UTZ Receptacle 17 Subminiature Tri-Start How to Order Proprietary Part Number Amphenol (R) Tri-Start connectors can be ordered by coded part number. Ordering procedure is illustrated by part number TVPS00RF-9-35PB( ) as shown below TVPS Connector Type Shell Style Service Class Shell Size Insert Arrangement Contact Type Alternate Positions Special Variations 00 RF 9 35 P B (XXX) Connector Type TV designates Tri-Start Series Connector TVP designates back panel mounted receptacle TVS designates 200 C rating TVPS designates back panel mounted, 200 C rated receptacle For other connector types, consult catalog 12-092. For how to order information on Composite Tri-Start Connectors (CTV), consult catalog 12-092. Shell Style 00 designates wall mount receptacle 01 designates line receptacle 02 designates box mount receptacle 06 designates straight plug 07 designates jam nut receptacle 09 designates flange mounted plug I designates solder mount receptacle, hermetic only Service Class RX non-conductive, anodic coated aluminum, 500 hour salt spray, 200 C (requires special variation suffix 005) RF electroless nickel plated aluminum, optimum EMI shielding effectiveness - 65dB @ 10GHz specification min., 48 hour salt spray, 200 C RGF same as RF, except for ground plane connectors RK corrosion resistant stainless steel, firewall capability, plus 500 hour salt spray resistance, EMI - 45 dB @ 10 GHz specification min., 200 C RW corrosion resistant olive drab cadmium plate aluminum, 500 hour extended salt spray, EMI - 50 dB @ 10GHz specification min., 175C RGW same as RW, except for ground plane connectors Y RS YN hermetic seal, passivated stainless steel, 200 C (non-hermetic connectors), nickel plated stainless steel, optimum EMI shielding effectiveness - 65 dB @10 GHz specification min., 48 hour salt spray, 200 C (hermetic connectors), nickel plated stainless steel, 200 C Shell Size MIL-C-38999, Size 9 - 25 A 9 B 11 C 13 D 15 E 17 F 19 G 21 H 23 J 25 MIL Shell Size Amphenol (R) Shell Size Insert Arrangement MIL-C-38999, see catalog 12-092 Contact Type P designates pin contacts S designates socket contacts Alternate Positions Locksmith keying - rotation of minor keys. See catalog 12-092. "N" not required for normal position Special Variations (100) eyelet termination (hermetic) (005) anodic coating 18 Subminiature Tri-Start How to Order Military Part Number To more easily illustrate ordering procedure by military designation, part number D38999/20F A35PB is shown as follows: D38999 / 20 Connector Type Shell Style Service Class Shell Size Insert Arrangement Contact Type Alternate Positions F A 35 P B Connector Type D38999/ designates MIL-C-38999 Series III Connector For how to order Composite Tri-Start (CTV) Connectors by military designation, consult catalog 12-092. Shell Style 20 designates wall mount receptacle 21 designates box mount receptacle, hermetic 23 designates jam nut receptacle, hermetic 24 designates jam nut receptacle 25 designates solder mount receptacle, hermetic 26 designates straight plug 27 designates weld mount receptacle, hermetic 29 designates Lanyard Release plug with pin contacts* 30 designates Lanyard Release plug with socket contacts* 31 designates Lanyard Release plug with MIL-STD-1760 pin contacts* * For ordering Lanyard Release Connectors, consult catalog 12-160. Ordering procedure for Lanyard Release Connectors includes specifying lanyard length codes and designating Stye 1 or 2. Amphenol(R) Y S N J M hermetic seal, passivated stainless steel, 200 C (non-hermetic connectors), nickel plated stainless steel, optimum EMI shielding effectiveness - 65 dB @10 GHz specification min., 48 hour salt spray, 200 C (hermetic connectors), nickel plated stainless steel, 200 C olive drab cadmium plate (175C) composite, environmental resisting, corrosion resistant electroless nickel plate (200C) composite, environmental resisting, corrosion resistant Shell Size MIL-C-38999, Size 9 - 25 A 9 B 11 C 13 D 15 E 17 F 19 G 21 H 23 J 25 MIL Shell Size Amphenol (R) Shell Size Insert Arrangement MIL-C-38999, see catalog 12-092 Contact Type H designates pin contacts (1500 cycle) J designates socket contacts (1500 cycle) P designates pin contacts (500 cycle) S designates socket contacts (500 cycle) Alternate Positions Locksmith keying - rotation of minor keys. See catalog 12-092. Use "N" for normal position Service Class C non-conductive, anodic coated aluminum, 500 hour salt spray, 200 C (environmental resisting) F electroless nickel plated aluminum, optimum EMI shielding effectiveness - 65dB @ 10GHz specification min., 48 hour salt spray, 200 C (conductive, environmental resisting) K corrosion resistant stainless steel, firewall capability, plus 500 hour salt spray resistance, EMI - 45 dB @ 10 GHz specification min., 200 C W corrosion resistant olive drab cadmium plate aluminum, 500 hour extended salt spray, EMI - 50 dB @ 10GHz specification min., 175C Amphenol(R) Federal Vendor Identification/FSCM 77820 19 Subminiature Tri-Start Specifications MIL-C-38999, Series III (TV) * 100% scoop-proof * High density contact arrangements * Contact sizes 12 through 22D plus size 8, 12, 16 coax, and size 8 twinax * Removable crimp, PCB, wire wrap, coax, triax, twinax and fiber optic contact styles available * Options include Hermetics, Filters and Thermocouples * Self-locking, quick disconnect threaded coupling * Corrosion resistant - shells of stainless steel or cadmium plate over nickel withstand a 500 hour salt spray exposure * Moisture resistance - improved interfacial seal design prevents electrolytic erosion of contacts * EMI shielding - designed to obtain metal-to-metal coupling, the TV connector provides a superior EMI shielding capability * Vibration/Shock - operates under severe, high temperature shock and vibration testing through 200 C * Firewall capability - available in stainless steel shell, Class K * Locksmith keying - 5 keyway polarization provides 5 alternate rotations * Shell grounding fingers are standard on all plugs * Triple-web grommet seal * DOD preferred * Available in a Fail Safe Lanyard Release plug * See catalog 12-092 Finish Anodic Coating (Non-Conductive) Electroless Nickel Olive Drab Cadmium Plate Nickel Base Stainless Steel with Nickel Plate Stainless Steel Olive Drab Cadmium Plate, Composite Electroless Nickel Plate, Composite Hermetic Connectors Suffix Material/Finish Stainless Steel Stainless Steel, Nickel Plate *** Add suffix (005) to part number Contact Size Crimp Well Data Well Diameter Nominal Well Depth Hermetic Well Data Min. Well Depth Contact Size CONTACT RATING Test Current Crimp Hermetic Maximum Millivolt Drop* Crimp** Hermetic** 22D 20 16 12 10 (Power) 5 7.5 13 23 33 3 5 10 17 NA 73 55 49 42 33 85 60 85 85 NA * Maximum Millivolt Drop data is determined by measuring resistance of mated contacts from end to end ** When using silver plated wire Well Diameter 22D 20 16 12 10 (Power) .0345 .0010 .047 .001 .067 .001 .100 .002 .137 .002 .141 .209 .209 .209 .355 .036 .044 .078 .116 +.004 -.000 +.004 -.000 +.004 -.002 +.004 -.002 NA .094 .125 .141 .141 NA FINISH DATA Non-Hermetic Shell Components Service Class Military C F W S K J M Proprietary RX*** RF RW RS RK RW RF Military Y N Proprietary Y YN SERVICE RATING Service Rating M N I II Suggested Operating Voltage (Sea Level) AC (RMS) 400 300 600 900 DC 550 450 850 1250 Test Voltage (Sea Level) 1300 VRMS 1000 VRMS 1800 VRMS 2300 VRMS Test Voltage 50,000 Ft. 550 VRMS 400 VRMS 600 VRMS 800 VRMS Test Voltage 70,000 Ft. 350 VRMS 260 VRMS 400 VRMS 500 VRMS Test Voltage 110,000 Ft. 200 VRMS 200 VRMS 200 VRMS 200 VRMS Please note that the establishment of electrical safety factors is left entirely in the designer's hands, since he is in the best position to know what peak voltages, switching surges, transients, etc. can be expected in a particular circuit. 20 Subminiature SJT Features, Part Number Breakdown * 100% scoop-proof - Basic LJT lengths * Basic JT mounting dimensions * Bayonet coupling * 5 key/keyway polarization with 4 alternate rotations * Rear release crimp contacts * PCB, wire wrap, twinax and coax contacts available * High density insert patterns available * Shell grounding fingers are an option on the plug * Options include Hermetics, Filters and Thermocouples * See catalog 12-091 See code below: 1. Connector Type SJT designates standard scoop-proof Junior Tri-Lock Connector SJTS designates high temperature connector SJTG designates plug with grounding fingers SJTP designates back panel mounted 2. Shell Style 00 designates wall mount receptacle 06 designates straight plug 07 designates jam nut receptacle I designates solder mount receptacle - hermetic 3. Service Class "Y" for hermetic applications, fused compression glass sealed inserts. Leakage rate less than .01 micron cu. ft./hr. (1 x 10-7 cc/sec.) at 15 psi differential, with interfacial seal. "RT" for environmental applications - supplied without rear accessories. Design provides serrations on rear threads of shells. For additional information defining complete description of service class, consult Amphenol, Sidney, NY. 4. SJT shell sizes available from 8 through 24. 5. - 66 designates insert arrangement 6. P designates pin contacts; S for socket contacts 7. A designates a rotated connector assembly (alternate keying). Other basic rotations are B, C and D. No letter required for normal, (no rotation) position 8. Finish variation suffix 1 2 3 4 5 6 7 8 SJT How to Order PART NUMBER To more easily illustrate ordering procedure, part number SJT00RT-18-66PA( ) is shown as follows: SJT 00 RT 18 66 P A () 21 MIL-SPEC Cross Reference Data and General Information MIL-Spec MIL-C-5015 Description Power type connectors, large contacts Older series had solder contacts; newer has crimp Amphenol Proprietary Mates CS, SM, TBF 10-72XXX, GP, SC, SF, SG, SB, FP, 10-214XXX, 10-244XXX, 10-87XXX, etc. PT, PT-SE, PT-CE, PTSDR, BP, SP, DC QWLD 10-193XXX, Class L 10-473XXX, HK - potted backshell Refer to applicable series. BTK, BTW, BTR, BTA, BNK, BYK, BYR, BYW, BYA, BTY, BYY Contact Termination & Removal Solder or crimp, front or rear removal Contact Sizes in Series (Wire Gauge) 16 thru 0 Coupling Method Threaded Other Notes 310X solder, 340X crimp F. R., 345X crimp R. R., GT Series Reverse Bayonet Coupling 311X solder, 312X crimp F. R. 347X crimp R. R. Class L Series is for heavy power. MS9055X Class "L" MIL-C-26482 * Series 1 crimp MIL-C-22992 Miniature connector. Contacts are medium size, both power and signal currents, solder or crimp Power type connector, heavy duty. MIL-C-5015 insert patterns, rugged. Solder or crimp contacts Series I mates with MIL-C-26482, 2 Series II mates with MIL-C-5015 Series III mates with MIL-C-26500 Solder or crimp, front or rear removal Solder for MS1734X, Crimp for Military Class "L" Crimp, rear removal 20, 16, 12 Bayonet thread, version Non-Military Threaded (quick thread), double stub 16 thru 0 MIL-C-83723 *Series I, II & III 20, 16, 12, 8, 0 Threaded and 83723/1 thru 14, bayonet, depend- 36 thru 49 Series I, ing on series 17 thru 27 -29 -30 -33 -34 -35 -50 -52 -53 Series II, 7X -8X -9X Series III Bayonet Intermates with Series I of MIL-C27599 Intermates with Series II of MIL-C27599 Available in Class K Firewall and Lanyard Release Breakaway Does not meet total performance requirements of Series III Intermates with Series III of MIL-C83723 M81511/0X F. R. M81511/4X R. R. MIL-C-38999 Subminiature - medium and high contact density, crimp contacts. Series I - scoop-proof Series II - lightweight, low profile Series I, LJT-R, (Also see MIL-C-27599 solder) Series II, JT-R, (Also see MIL-C-27599 solder) Crimp, rear removal 22D, 20, 16, 12, and coax sizes 8, 12, 16 22D, 20, 16, 12, and coax sizes 12, 16 22D, 20, 16, 12, and coax sizes 8, 12, 16 22D, 20, 16, 12, and coax sizes 8, 12, 16 20, 16, 12 Crimp, rear removal Bayonet Series III - High performance, but suited for general duty Series IV Breech-Lok, expensive design, can be difficult to mate MIL-C-26500 Miniature connector. Contacts are medium size, both power and signal, solder or crimp Subminiature - medium and high contact density, crimp contacts. Series I & II - front release contacts Series III & IV - rear release contacts Subminiature, similar to MIL-C38999 except has non-removable solder contacts. Fully mateable with MIL-C-38999 Series III, TV-R, T3W, T3K, Crimp, rear removal T3F, T3S, T3N, T3Y, Series III CTV - Composite None Crimp, rear release Threaded Breech-Lok ZZW, ZZL, ZZY, ZZB Crimp, front removal Bayonet and Threaded Bayonet MIL-C-81511* 348 Series Crimp, front (gang) & rear removal 22, 20, 16, 12 MIL-C-27599 LJT-T, P - Series I LJT-A, C, P - Series II Solder 22, 20, 16 Bayonet Intermates with Series I and II of MILC-38999 * Denotes inactive 22 |
Price & Availability of MS311XXX-XXX
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |